CATHODE RAY TOMES

VS PAK Instructions

VS. PAK (Universal conversion kit) (Nintendo) · Document · 19 pages · 6 sections · original scan

Page 1

1-800-633-3236

VS.- PAK

For. VS.UniSystem"; VS.DualSystem™ and VS.Table

INSTRUCTIONS

Contents of Pak:

PPU ROM Kit

Nameplate Overlay Center Piece Label (Upright)

Instruction Label (Table)

Operation Manual

Dip Switch Settings Instruction Label

Factory Recommended Settings Sheet VS. Pak Instruction Sheet

VS. Nameplate Glass (DualSystem)

VS. Nameplate Plexiglass (UniSystem) Cardboard Header

Authorization Label

Header Strips

a Header Angle

INTRODUCTION

This Pak contains parts to change any VS. UniSystem™ or VS. DualSystem™ game. Please be sure to save your PPU ROM kit and literature from the VS. game you are converting so you can change back to that VS. game if you so desire. By doing this, you will be able to build a library of games for your VS. Systems.

Tools needed: small flathead screwdriver medium phillips head screwdriver staple gun

Page 2

VS. UPRIGHT PAK INSTALLATION PROCEDURE

I. New Style Nameplate Overlay

A. Adhere header strips to the back of plexiglass and glass as shown:

VS. UniSystem™ VS. DualSystem™ HEADER STRIPS | LI -

HEADER STRIPS

PLEXIGLASS

SCOTCH TAPE SHOWN: VS, UniSystem

NAMEPLATE OVERLAY

B. Adhere Authorization label to the new nameplate overlay where it will not cover any instructions or the game name.

C. Using scotch tape (not provided), tape new nameplate overlay to the back of either UniSystem™ plexiglass or DualSystem™ glass depending on which game the pak is being installed in first.

Note: This new header system allows the same nameplate overlay to be moved between Uni plexiglass and Dual glass an unlimited number of times.

D. Remove four (4) top trim screws and top trim. (See Illus. 1-2 and 1-3)

E. Slide old nameplate up and out of game. (See Illus. 1-2 and 1-3)

F. Replace nameplate and top trim. Be sure that nameplate fits under plastic center trim and that the left and right sides are correct. NOTE: Do not tighten top trim screws until next step.

Page 3
Note: Gumshoe is the first pak which uses this new interchangeable nameplate overlay system. Older VS. Pak overlays should be cut to the new size shown below and a sheet of clear mylar placed over the adhesive. This will make older VS. Pak overlays compatible with the new system. 22%,"

5 She ; new size

II. Cardboard Header

A. Fold cardboard header and slide under top trim. Tighten top trim screws. (See Illus. 1-2 and 1-3)

III. Center Piece Label (VS. DualSystem™ only)

A. Remove old center piece label (if necessary). (Illus. 1-2)

B. Clean surface and adhere new center piece label, being careful to center it.

Iv. PPU ROM Kit

A. Replace ROMs and PPUs as shown in VS. Game Operation Manual.

V. Factory Recommended Dip Switch Settings

A, Check dip switch settings on P.C. board so they match the factory recommended dip switch settings sheet.

VI. Dip Switch Settings Instruction Label

A. Peel off backing sheet and staple label on back door next to old label. NOTE: Do not remove old label! Se

cardboard header cardboard header ;

Page 4

Il.

Ill.

Iv. VS. TABLE PAK INSTALLATION PROCEDURE

Instruction Label (See Illus. 1-4)

A.

Dip

PPU Open table housing, remove the four (4) nuts holding the plexiglass instruction label cover, and remove the plexiglass cover.

Remove old instruction label carefully and save for future use.

Remove paper backing strip on new label and install.

Replace plexiglass cover.

Switch Settings Instruction Label

Remove paper backing on label and place on any unused surface inside table housing. (Remove old label if necessary. Save for future use.)

ROM Kit

Replace ROMs and PPUs as shown in VS. Game Operation Manual.

Factory Recommended Dip Switch Settings

A. Check dip switch settings on P.C. board so they match the factory recommended dip switch settings sheet.

Page 5

FINAL CHECK SHEET

O FCC door installed correctly

0 Nameplate overlay installed correctly with header strips in place

O Dip switch set correctly (See factory recommended sheet for this particular game)

O All play buttons and controllers function correctly

oO Color on monitor looks good

O Coin acceptors give credit

Page 6

For VS. Unisystem™, vg. pualsysten™M, and VS. Table

INSTRUCTIONS

Contents of Pak:

PPU ROM Kit

Nameplate Overlay

Center Piece Label (Upright) Instruction Label (Table)

Monitor Bezel

12 Black Adhesive Dots PRP RP RB

Operation Manual

Dip Switch Settings Instruction Label

Factory Recommended Settings Sheet

VS. Pak Instruction Sheet

VS. Nameplate Glass (DualSystem) VS. Nameplate Plexiglass (UniSystem) Cardboard Header PPP PPP BB

Authorization Label

INTRODUCTION This Pak contains parts to change any VS. UniSystem! or VS. Dualsystem!™ game. Please be sure to save your PPU ROM kit and literature from the VS. game you are converting so you can change back to that VS. game if you so desire. By doing this, you will be able to build a library of games for your VS. Systems.

Tools needed: small flathead screwdriver medium phillips head screwdriver staple gun

QQ)

Page 7

VS. UPRIGHT PAK INSTALLATION PROCEDURE

I. Nameplate Overlay Duck Bunt

an A. Adhere nameplate overlay to plexiglass or glass Hogan's Alley nameplate and trim. NOTE: Be sure to center ONLY! 1 fowan (See Illus. 1-1) r Hl i ¥

  • =<SSS SSS SSS == 73; Deals tandae eccseeeeeeeseeeeee , right side H , right side \

B. Remove four (4) top trim screws top trim. (See Illus. 1-2 and 1-3) a=!

C. Slide old nameplate up and out of game. (See Tllus. 1-2 and 1-3)

D. Replace nameplate and top trim. Be sure that nameplate fits under plastic center crim and that the left and tight sides are correct. NOTE: Do noc tighten top trim screws until next step.

E. Place authorization label on nameplate overlay.

II. Cardboard header

A. Fold cardboard header and slide under top trim. Tighten top trim screws. (See Illus. 1-2 and 1-3)

III. Center Piece Label (VS. DualSystem only)

A. Remove old center piece label (if necessary). (Illus. 1-2)

B. Clean surface and adhere new center piece label, being careful to center it.

IV. Bezel

A. The play field for some games is slightly narrower than previous games; therefore, to eliminate any unwanted borders on the screen, please install the cardboard bezel. (See Illus. 1-2)

B. Slide the six (6) tabs under the edge of the existing bezel.

C. To prevent light leakage and movement of bezel, place the provided black dots in the corners of each tab. There are two (2) corners per tab, twelve (12) per bezel.

(2)

Page 8

IV. PPU ROM Kit

A. Replace ROM's and PPU's as shown in VS. Game Operation Manual.

V. Factory Recommended Dip Switch Settings

A. Check dip switch settings on p.c. board so they match the factory recommended dip switch settings sheet.

VI. Dip Switch Settings Instruction Label

A. Peel off backing sheet and staple label on back door next to old label. NOTE: Do not remove old label!

cardboard healer —> a

center piece label

(3)

Page 9

Il.

Ill.

Iv. VS. TABLE PAK INSTALLATION PROCEDURE

Instruction Label (See Illus. 1-4)

A.

Dip

PPU Open table housing, remove the four (4) nuts holding the plexiglass instruction label cover, and remove the plexiglass cover.

Remove old instruction label carefully and save for future use.

Remove paper backing strip on new label and install.

Replace plexiglass cover.

Switch Settings Instruction Label

Remove paper backing on label and place on any unused surface inside table housing. (Remove old label if necessary. Save for future use.)

ROM Kit

Replace ROMs and PPUs as shown in VS. Game Operation Manual.

Factory Recommended Dip Switch Settings

A. Check dip switch settings on P.C. board so they match the factory recommended dip switch settings sheet.

Page 10

FINAL CHECK SHEET

O FCC door installed correctly

0 Nameplate overlay installed correctly with header strips in place

O Dip switch set correctly (See factory recommended sheet for this particular game)

O All play buttons and controllers function correctly

oO Color on monitor looks good

O Coin acceptors give credit

Page 11

INSTRUCTIONS

Contents of Pak

PPU ROM Kit

Nameplate Overlay (R)

Nameplate Overlay (L) Instruction Label (Upright)

Instruction Label (Table)

Monitor Bezel (Upright) Black Adhesive Dots (Upright)

Baseball Operation Manual

Dip Switch Settings Instruction Label

Factory Recommended Settings Sheet BRP ee RN NPE PB

VS. PAK Instruction Sheet

INTRODUCTION

This kit contains parts to change any VS. Tennis (Upright or Table) into a VS. Baseball. Please be sure to save your PPU ROM Kit and literature for VS. Tennis so you can change back to VS. Tennis if you so desire. By doing this, you will be able to build a library of games for your VS. System.

Page 12

I.

Il.

Ill. VS. UPRIGHT

PAK INSTALLATION PROCEDURE

Nameplate Overlay

A. Remove eight (8) top trim screws and both top trims. (See Illus. 1-1)

B. Slide both nameplates up and out of game. (See Illus. 1-1)

C. Peel off nameplate overlays and clean glass with alcohol or lacquer thinner.

D. IMPORTANT! PLEASE NOTE THAT THERE IS A RIGHT AND LEFT NAMEPLATE OVERLAY. (See Illus. 1~2)

E. Peel off the paper backing from one end of the overlay and apply to end of glass, making sure overlay is centered.

F. Peel back the remaining backing, adhering new nameplate overlay. Be sure to remove any air bubbles.

G. Trim off excess flush with the angled ends of glass.

H. Replace nameplates and top trim. Be sure that nameplates fit under plastic center trim and that the left and right sides are correct.

NOTE: If you wish to collect the nameplates to match your PPU ROM Kits, you should buy two (2) blank nameplate glass (available from your distributor) and mount your new overlays on these. This way you can change your game back anytime you wish and continue to build a library of games for your VS. System.

Instruction Label

A. Remove old instruction label. (See Illus. 1-1)

B. Clean surface and adhere new instruction label, being careful to center it.

Bezels

A. The play field for VS. Baseball is slightly narrower than VS. Tennis; therefore, to eliminate any white borders on the screen, please install the two (2) cardboard bezels.

B. Slide the six (6) tabs under the edge of the existing bezel.

C. To prevent light leakage and movement of bezel, place the provided black dots in the corners of each tab. There are two (2) corners per tab, twelve (12) per bezel.

Page 13

IV. PPU ROM Kit

A. Replace ROM's and PPU's as shown in VS. Baseball Operation Manual.

V. Factory Recommended Dip Switch Settings

A. Check dip switch settings on P.C. board so they match the factory recommended dip switch settings sheet.

VI. Dip Switch Settings Instruction Label

A. Peel off backing sheet and staple label on back door next to old label. NOTE: Do not remove old label!

Nameplate overiay

Instruction label

NOTE: The overlay instruction area goes on the left and right Sea.
Page 14

Il.

Ill.

Iv. VS. TABLE

PAK INSTALLATION PROCEDURE

Instruction Label (See Illus. 1-3)

A. Open table housing, remove the four (4) nuts holding the plexiglass instruction label cover, and remove the plexiglass cover.

B. Remove paper backing strip on new label and place over old label.

C. Replace plexiglass cover.

D. Repeat operation for other side.

Dip Switch Settings Instruction Label

A. Remove paper backing on label and place on any unused surface inside table housing.

PPU ROM Kit

A. Replace ROM's and PPU's as shown in VS. Baseball Operation Manual.

Factory Recommended Dip Switch Settings

A. Check dip switch settings on P.C. board so they match the factory recommended dip switch settings sheet.

Page 15

1-800-633-3236

VS.- PAK

For VS. UniSystem™, vs. Dualsystem™, and VS. Table

INSTRUCTIONS

Contents of Pak:

PPU ROM Kit

Nameplate Overlay Center Piece Label (Upright) Instruction Label (Table) Operation Manual Dip Switch Settings Instruction Label Factory Recommended Settings Sheet

VS. Pak Instruction Sheet

VS. Nameplate Glass (DualSystem) VS. Nameplate Plexiglass (UniSystem)

Cardboard Header et Authorization Label

INTRODUCTION This Pak contains parts to change any VS. UniSystem™ or VS. DualSystem™ game. Please be sure to save your PPU ROM kit and literature from the VS. game you are converting so you can change back to that VS. game if you so desire. By doing this, you will be able to build a library of games for your VS. Systems.

Tools needed: small flathead screwdriver medium phillips head screwdriver staple gun

qd) 9/85

Page 16

VS. UPRIGET PAK INSTALLATION PROCEDURE

I. Nameplate Overlay Duck Hunt and A. Adhere nameplate overlay to plexiglass or glass Hogan's Alley nameplate and trim. NOTE: Be sure to center ONLY! carefully. (See Illus. 1~1)

! | | EG vera oss SSS SS SS

VS. UniSystem header VS. DualSystem header + right side y LoST STS SS SSS SSS SSS i-1 B. Remove four (4) top trim screws and top trim. (See Illus. 1-2 and 1-3)

C. Slide old nameplate up and out of game. (See Illus. 1-2 and 1-3)

D. Replace nameplate and top trim. 3e sure that nameplate fits under plastic center trim and that the left and right sides are correct. NOTE: Do not tighten top trim screws until next step.

E. Place authorization label on nameplate overlay.

II. Cardboard header

A. Fold cardboard header and slide under top trim. Tighten top trim screws. (See Illus. 1-2 and 1-3)

III. Center Piece Label (VS. DualSystem only)

A. Remove old center piece label (if necessary). (Illus. 1-2)

B. Clean surface and adhere new center piece label, being careful to center it.

  • 9/85
Page 17

IV, PPU ROM Kit

A. Replace ROM's and PPU's as shown in VS. Game Operation Manual.

v. Factory Recommended Dip Switch Settings

A. Check dip switch settings on p.c. board so they match the factory recommended dip switch settings sheet.

VI. Dip Switch Settings Instruction Label

A. Peel off backing sheet and staple label on back door next to old label. NOTE: Do not remove old label!

cardboard header = a

center piece label

  • 9/85
Page 18

I.

Il.

IIl.

Iv. VS. TABLE PAK INSTALLATION PROCEDURE

Instruction Label (See Illus. 1-4)

A. Open table housing, remove the four (4) nuts holding the plexiglass instruction label cover, and remove the plexiglass cover.

Remove old instruction label carefully and save for future use.

Remove paper backing strip on new label and install.

Replace plexiglass cover.

Switch Settings Instruction Label

Remove paper backing on label and place on any unused surface inside table housing. (Remove old label if mecessary. Save for future use.)

ROM Kit

Replace ROM's and PPU's as shown in VS. Game Operation Manual.

Factory Recommended Dip Switch Settings

A. Check dip switch settings on p.c. board so they match the factory recommended dip switch settings sheet.

  • 9/85
Page 19

FINAL CHECK SHEET

Fcc door installed correctly

( Nameplate overlay installed correctly

O Dip switch set correctly (See factory recommended sheet for this particular game)

( All play buttons and controllers function correctly

O Color on monitor looks good

(] Coin acceptors give credit

(5) 9/85