CATHODE RAY TOMES

Tekken 3 Operations Manual

Tekken 3 (World, TET2/VER.E1) (Namco, 1997) · Manual · 28 pages · 13 sections · original scan

Page 1

TEKKENS3

OPERATION MANUAL

@Be sure to read this manual and the instruction manual for cabinet to be used before installing and operating this game /\ CAUTION machine to ensure the safety and to operate correctly Keep this manual with care so as to read in case of need in daily operation

Page 2

Introduction

Thank you for purchasing our TEKKEN 3 (hereinafter mentioned as the game machine). This manual shows you how to operate, install, transport, remove, maintain and discard this game machine in safety. Be sure to read this manual and the instruction manual for cabinet to be used before installing and operating this game machine to ensure the safety and to operate correctly. This manual applies to a staff of a game center. However, an article indicated as “It must be handled by an engineer.” applies to engineers, so the operation must be done by engineers only. Never someone else besides the engineer should operate it.

Engineer means the following personnel: Personnel who had taken credits of mechanical or electrical engineering in university, college or highschool, or who have knowledge as same as one who had taken the above credits and also who maintains, takes care and repairs amusement machines as a daily work.

When an owner of this game machine leaves operation, installation, transportation, removal, maintenance and discard to the other person, instruct him/her to read the articles in point and to follow the regulations. Keep this manual with care so as to read in case of need in daily operation. In case of resell of the game machine, be sure to attach this manual to the PC board.

For inquiries about the game machine and servicing: As for inquiries about the game machine and servicing for the machine, contact your distributor.

Page 3

Introduction Table of Contents lable of Contents

  • Precautions on safety (for aa Operation) 1-1 Explanation for asym! ch. for calling attention: 1-2 Explanation for signal words | WARNING. A CAUTION) _ 1-3 Precau ition on Safety for operators in charge of Installation (It should be handled by an engineer.) 1-4 Precaution on Safety for Operator in charge of Maintenance (It should be handled by an engineer.) 1-5 Precautions on Safety with regard to Discard
  • Packing Substance Check
  • Specifications 3-1 Control Panel 3-2 Monitor 3-3. PC Board
  • Installation 4-1 Connection to a Cabinet corresponding to JAMMA standard 4-1-1 | Connection of Control Panel 4-1-2 Connection of | ard 4-1-3 Connection of ! ker 4-2. Connection to a Cabinet corresponding to JAMA VIDEO standard (JVS) 4-2-1 Connection of Control Panel 4-2-2 Connection of PC Board
  • Adjustment \djusting Switch lode 5-2-1 DISPLAY TEST 5-2-2. SWITCH TEST 5-2-3. SOUND TEST 5-2-4 JVS CABINET OPTIONS 5-2-5 GAME OPTIONS 5-2-6 COIN OPTIONS 5-2-7 ADS. 5-2-8 DATA CLEAR 5-2-9 EXIT & SAVE (Exit of TEST mode)
  • Maintenance (It must be handled by an engineer)
  • Transportation
  • PC Board Edge Connector List

A

{Note DcCcecocwmamdIuaAuununawe NNNNNNNNKHE BER ANRARBRWONSHABRWHN

WARNING Do NOT remodel this game machine without our agreement; otherwise. an unexpected danger may happen.

® The contents on this operation manual are subject to change without notice for improvement.

Page 4

1. Precautions on safety (tor satey operation)

1-1 Explanation for a symbol A\ for calling attention:

The meaning of the symbol QM tor calling attention on this manual is as follows: The symbol & for calling attention shows a potential danger and means not only an unspecified but general notice for dangers, warnings and cautions. All of notices indicated by this mark are concerned with safety.

1-2 Explanation for signal words (4\ WARNING, A\ CAUTION)

On this manual, these signal words (42 WARNING, 4 CAUTION) show a danger level for person and a damage level for property which have a possibility to occur.

WARNING In the case that an operator would be killed or seriously wounded

if he/she makes a mistake in the operation

In the case that an operator would be slightly wounded or that

CAUTION | only the property will be damaged if he/she makes a mistake in the | operation.

These levels mentioned above are as follows:

  • Classification for the damage A serious wound: Loss of eyesight, an injury, a burn (by high or low temperature), an electrical shock, a fracture of a bone or poisoning which leaves an aftereffect and needs admission to a hospital or going to hospital for a long term for treatment. Slight wound: A wound which does not need admission to a hospital or going to hospital for a long term for treatment. (A wound except for mentioned above.) Property damage: Large scale damage relating to the building, property, livestock or pets.
Page 5

1-3 Precaution on Safety for operators in charge of Installation

(It should be handled by an engineer.) —S— ee

[Notice]

®@ This game machine corresponds to both of JAMMA standard and JAMMA VIDEO standard (JVS). The notice on safety differs with regard to installation because that the connecting procedures and others differ depending on a standard. Be sure to read the article corresponding to the standard after confirming the standard €or the cabinet by reading the manual for cabinet to be used.

<For a cabinet corresponding to JAMMA standard>

® Be sure to turn OFF the power of cabinet to be used before installation and removal of PC board; otherwise, an operator may be struck by electricity. Be sure to connect +5V (2.5A or more) and +12V (2.0A or more) correctly for power of PC board; otherwise, a wrong connection may cause an accident, such as a fire, and trouble. The voltage should be used within the range of + 5%; otherwise, an accident, such as a fire, and trouble may happen.

<For a cabinet corresponding to JAMMA VIDEO standard (JVS)>

© Be sure to turn OFF the power of cabinet to be used before installation and removal of PC board; otherwise, you may be struck by electricity.

WARNING | @ Be sure to connect +5V (2.5A or more) correctly for power of PC board; otherwise, a wrong connection may cause an accident, such as a fire, and trouble. ®@ The voltage should be used within the range of +5% ; otherwise, an accident, such as a fire, and trouble may happen.
Page 6

1-4 Precaution on Safety for Operator in charge of Maintenance

(It should be handled by an engineer.)

® Do NOT remodel this game machine without our agreement; otherwise, an unexpected danger may happen. Be sure to torn OFF the power switch of the cabinet before maintenence work; otherwise, an operator or anothwr oie may be injured or struck by electricity.

1-5 Precautions on Safety with regard to Discard

| @ If this game machine Is discarded, perform gathering transportation and disposal » orks in the procedure based on « law.

CAUTION | @ If an owner of this game machine leaves gathering transportation and disposal works for discard to the other person, entrust a professional with cach operation.
Page 7

2. Packing Substance Check

This game machine consists of the followings.

[Notice] @ Make sure that the following substances are complete.

Name Description | Qty

Gan PC bond, “TEKKEN b)|System 12 PC board|
Operation manualThis manual1
Tith fae-|Logo “TEKKEN 3" is described.|
| B sticker ;«;Oblong sticker for explanation of controls1
Button seal (|1 sheet printed for two playersI|

Kick hamess ¢ ” Wired 48P extension edge connector 1

*1) On the adhesive side of A sticker, B sticker and button seal, a “release type”’ bonding agent, which is hard to leave a mark after peeling it off, is used.

*2) This game machine corresponds to both of JAMMA standard and JAMMA VIDEO standard (JVS). The kick harness is not necessary if the PC board is connected to a cabinet corresponding to JAMMA VIDEO standard (JVS). (Refer to “3-3 PC Board” for connection terminal of each standard.)

Page 8

3. Specifications

3-1 Control Panel

2-P specifications = 8-direction lever : 1x2 = Button switch : 4x2 = Start switch : 1x2

PI-START switch P2-STARTswitch

Wf-4 “Yip “laigri git, MECUYYAETA whyty

  • 8-direction lever

3-2 Monitor

Direction of monitor: Horizontal Scanning retrace line format: Interlace/non-interlace: selectable Synchronizing signal: Composite/separate: selectable (1) Horizontal synchronizingfrequency: 15.75 kHz Vertical synchronizing frequency: 60.0 Hz

*1) Only for connection of cabinet corresponding to JAMMA VIDEO standard (JVS)

Page 9

3-3 PC Board

The PC board corresponds to both of JAMMA standard and JAMMA VIDEO standard (JVS)

Size : 260 x 230 (mm) (excluding part projected) Power supply (when connecting JAMMA standar( terminal) : +5V +5% (2.5A or more), +12V 5% (2.0A or more) Power supply (when connecting JAMA VIDEO standard (JVS) terminal): +5V £5% (2.5A or more)

48P extension edge connector / S6P edge connector (JAMMA)

Audio output Connector 2 Audio output connector 1

Video output connector 2

Video output connector 1

DC power connector

*1) Used to connect to a cabinet corresponding to JAMMA standard. *2)Used to connect to a cabinet corresponding to JAMMA VIDEO standard (JVS).

Page 10

4.

4-1

Installation

[Notice]

® This game machine corresponds to both of JAMMA standard and JAMMA VIDEO standard (JVS). Be sure to read the article corresponding to the standard after confirming the standard for the cabinet by ceeding he manual for cabinet to be used. The mark is indicated on the article for cabinet corresponding to JAMMA standard, and the mark is indicated on the article for cabinet corresponding to JAMMA VIDEO standard (JVS).

Connection to a Cabinet corresponding toJAMMA standard BEI

[Notice]

Use +12V or less for line voltage of coin counter.

4-1-1 Connnection of Control Panel

Connect the JAMMA edge connector and kick harness (wired 48P extension edge connector) packed together to each appropriate switch of control panel with reference to “8.PC Board Edge Connector List”.

[Notice]

@ Be sure to use a JAMMA standard conformable one and a specified one for the JAMMA edge connector. @ Be sure to use a NAMCO specified one (DDK-made: 225D-10024C2-3312) for the 48P extension edge connector. ®@ Do not connect anything to the blank column on “8.PC Board Edge Connector List” ® Connect each switch and lever input of edge connector to N. O. terminal, such as micro switch and etc. @ Le sure to connect the COM terminal to GND of edge connector for the micro switch wired.

Page 11

| Connection to a Cabinet corresponding to JAMMA VIDEO

standard (JVS)

4-2-1 Connection of Control Panel

After being sure to read the manual for cabinet to be used, connect the suitable control panel for this game machine (Refer to “3-1 Control Panel”.) to the cabinet.

4-2-2 Connection of PC Board

©@ Se sure to turn OFF the power of cabinet to be used before installation and removal of PC board; otherwise, you may be struck by electricity.

WARNING | ©@ Be sure to connect +5V (2.54 or more) correctly for power of PC board: otherwise, a wrong connectionmay cause 4m sccident, such as a fire, and trouble.

@ The voltage should he used within the range of £5%; otherwise an accident, such as 2 fire, and trouble may happen.

After being sure to read the manual for cabinet to be used, connect the PC board according to the following procedures Refer to “1-3 Replacement of game PC board on the instruction manual for “CYBERLEAD” if the "CY BERLEAD” made by NAMCO is used as a cabinet.

  • Open the PC board loading section of cabinet. If another PC board has been already connected, remove it.
  • Install the PC board for this game machine in the PC board loading section correctly so that the cable becomes cesy to be connected. (The following figure shows the case that the cabinet “CYBERLEAD” made by NAMCO i used.)

}to the \ |cabinet /

“TEKKEN 3” game PC board

Gy hase (Wooden)

Page 12
  • Connect the cable at cabinet side to the concerned connector on the PC board correctly. (Refer to figure below.)

Cable at cabinet side "TEKKEN 3" game PC board (Side)

® Cable: Sectional terminal is S888 (Standard I/O) RED WHITI

+ RED or "R”:to one of red terminals

  • WHITE or "L": to one of while terminals

e = Possible to connect to both of them.

=| (Power) |

  • Close the PC board loading section of cabinet. © Cable: Sectional terminal is |=

[Notice]

@ It is allowed to display the original messages and graphics, which are linked with the game contents of the game machine, on the LED dot-matrix display only if the game machine is used with the cabinet "CYBERLEAD" made by NAMCO. For that purpose, it is necessary to transmit the graphic data to the cabinet in advance. If the original graphic data of the game machine is not transmitted, the following screen is displayed before displaying the game screen when turning ON the power of cabinet. (If the data has been already transmitted, it is not displayed. The mode is shifted to the game mode immediately.)

Page 13

After selecting "YES" or "NO" by moving the P1:8-direction lever up and down, settle it with PI-BUTTON 1.It is automatically settled after 10 seconds approximately even if the PI-BUTTON 1 is not pressed. In any case, the item displayed in red is supposed to be selected. If "NO" is selected, the transmission is not performed, and then the screen above is displayed again when turning ON the power at the next time. If "YES" is selected, the following screen is displayed, and then the data transmission is performed.

ee ees 2 Display of the progress of transmitting operation (Finish at the right end.)

Display how to interrupt the data transmission.

The usual game mode is shifted after finishing the data transmission. The original display of the game machine appears on the LED dot-matrix display. After that, it is not necessary to transmit the data again unless the LED display data in cabinet is initialized (Refer to "6-1-3 Explanation of display contents and how to change it" on the instruction manual "CYBERLEAD".), or unless the data transmission of another game machine is perfomed. If the P1-BUTTON 1 and P1-START switches are pressed at the same time while operating the data transmission, the operation is interrupted, and then the usual game mode is shifted. In this case, it is necessary to transmit the data again when turning ON the power at the next time in order to display the original display of the game machin on the LED dot-matrix display.

Page 14

5.

5-1

Adjustment

Adjusting Switch

The adjusting switch on the PC board is as follows:

  • Optional switch This switch is a pair of two units. If the #1 is “ON”, the mode is in TEST mode. If the #2 is “ON”, the screen is in STOP. All of switches is usually “OFF”.

[Notice] @ Thenomal game is not allowed to be performed if the optional switch #2 is in “ON” state.

  • Speaker volume Turning it clockwise, the volume of speaker becomes large. Turning it counterclockwise, the volume of speaker becomes small.

[Notice]

®@ The speaker volume can not work for volume adjustment, if the cabinet corresponding to JAMMA VIDEO standard (JVS) is used. After being sure to read the manual for cabinet to be used, perform volume setting at cabinet side.

Speaker volume Optional switch

Page 15

the test menu screen is displayed. Use the test switch on the cabinet (Referto “8. PC Board Edge Connector List” to perform connection.) or the optional switch on the PC board. (Refer to “5-1 Adjusting switch”.) After selecting an item (displayed in red) on the test screen by moving the P1:8-direction lever up and down, press the PI-BUTTON 1 to display the selected test screen.

[Notice]

@ The “JVS CABINET OPTIONS” is not allowed to be selected if the PC board is connected from the JAMMA edge connector. It is allowed to be selected only if the PC board is connected from the connector corresponding to JAMMA VIDEO standard (JVS).

When exiting the TEST mode , be sure to select “EXIT & SAVE” from the test menu screen as below before pressing PI1-BUTTON 1 to end it.

DISPLAY TEST (5-2-1) WITCH TEST (5-2-2) OUND TEST IVS CABINET OPTIONS (5-2-4) (GAME OPTIONS (5-2-5) COIN OPTIONS (5-2-6) ‘ADS. DATA CLEAR EXIT & SAVE (Exit of TEST mode) (5-2-9)

[Notice]

@ If the procedure above is not used for exiting of TEST mode, a changed setting may not be reflected correctly. Be sure to select “EXIT & SAVE” from the test menu screen before pressing P1-BUTTON 1 to end it.

@ In both cases that the test switch on the cabinet is the slide type and that the optional switch #1 on the PC board is used, take note of the followings. » The mode enters the TEST mode when switching the test switch on the cabinet or the optional switch #1 on the PC board to ON from OFF. If the switch has been turned ON before the mode enters TEST mode, turn it ON again after turning it OFF once. « The test mode is not exited even if the test swilc li 1s turned OFF. Be sure to select “EXIT & SAVE” from the test menu screen before pressing P1- TT UN 1 to end it.

Page 16

i DISPLAY TEST

This mode performs test and setting on the screen display. The DISPLAY TEST provides 1 kind of common display and 3 kinds of test pattern.

  • COLOR EDIT This screen performs balance adjustment for brightness and color tone of display signal output from the PC board.
  • DIAGONAL This screen is used for display check in interlace mode.
  • COLORBAR This screen is used for balance check and adjustment for brightness and color tone.
  • CONVERGENCE This screen is used for check and adjustment for display size, display position, ratio length to breadth and distortion.

The screen (1), which is the common display, is displayed so as to overlap on the screens (2) to (4). Press P1-BUTTON 3 to select if screen (1) is displayed or not. The screens (2) to (4)are the test display, The screen (2) is displayed immediately after entering DISPLAY TEST mode. Press PI-BUTTON 1 to select the screen in order of (2),(3), (4)and (2) repeatedly. Pressing P1-START switch, the DISPLAY TEST mode exits and then the test menu screen appears.

  • COLOR EDIT This screen performs balance adjustment for brightness and color tone of display signal output from the PC board.

Non Interlace Scanning retrace line format on monitor Contrast: Whole contrast Bright R: Brightness (RED) Bright G: Brightness (GREEN) Bright B: Brightness (BLUE)

PREVIOUS VALUE:PI-BUTTON 4Display how to return a value to the initial value.
EXIT COLOR EDIT:P1-BUTTON 3Display how to exit the COLOR EDIT mode.
NEXT COLOR TEST:P1-BUTTON1Display how to advance to the next test pattern.

EXIT: P1-START Display how to return to the test menu screen.

The above screen appears while overlapping on the test pattern. After selecting an item to be changed by moving the P1:8-direction lever up and down, move it right and left to change the setting. Pressing P1-BUTTON 4, all of contents changed on the COLOR EDIT screen are canceled. Pressing P1-BUTTON 3, the COLOR EDIT screen is suspended, and then the display of setting items disappear. Pressing P1-BUTTON 3 once again, the setting items are displayed again, and then the COLOR edit screen becomes available.

Pressing PI-START switch, whole DISPLAY TEST exits, and then the test menu screen appears.

Page 17
  • DIAGONAL This screen is used for display check in interlace mode. «,

a 7 — —> DIAGONAL

ENTER COLOR EDIT: P1-BUTTON 3 Display how to enter the COLOR EDIT mode. NEXT COLOR TEST: P1-BUTTON 1 Display how to advance to the next test pattern. \_EXIT: P1-START_ _ Display how to return to the test menu screen.

The diagonal pattern is displayed on the screen, Press P1-BUTTON 2 to select the color of diagonal pattem in order of WHITE, BLUE, RED, VIOLET, GREEN. LIGHT BLUE, YELLOW, BLACK and WHITE repeatedly Press P1-BUTTON | to switch the mode to the next test pattern (COLOR BAR). Press PI-BUTTON 3 to select if the COLOR EDIT screen is displayed or not. (Refer to “(1) COLOR EDIT" on this article.) Pressing P1-START switch, the DISPLAY TEST exits, and then test menu screen appears,

[Notice] @ This test pattern is mainly used to check the screen display in interlace mode ,«;,. The interlace mode allows to display more precise than the non-interlace mode ,-2). However, the screen may not be displayed correctly depending on the monitor to be used due to its property, If the errors, such as dispersion of diagonal, severe flickering on the whole screen and etc., appear on the screen above i interlace mode, use it after switch the mode to “Non-interlace” from “Interlace” in the COLOR EDIT screen. (Refer to “(1) COLOR EDIT" on this article.)

  • Interlace mode This display mode allows to do double vertical resolution without change of horizontal/vertical frequencies if the display position of only half line is shifted in vertical direction intentionally once of twice screen displays. This mode allows to display more precise and more smooth curved and straight lines than the noninterlace mode. (The “CYBERLEAD” made by NAMCO provides the interlace mode as standard setting.) *2) Non-interlace mode This display mode shows the routine screen display at the fixed position against “Interlace mode”.

ais

Page 18
  • COLOR BAR This screen is used for balance check and adjustment for brightness and color tone.

COLOR BAR

COLOR BAR (WHITE)

COLOR BAR (RED)

COLOR BAR (GREEN)

COLOR BAR (BLUE)

ENTER COLOR EDIT: P1-BUTTON 3 Display how to enter the COLOR EDIT mode. NEXT COLOR TEST: P1-BUTTON 1 Display how to advance to the next test pattern. EXIT: P1-START Display how to return to the test menu screen.

The color bar with brightness gradation is displayed. Press P1-BUTTON 2 to select the phase of gradation in order of 32, 16,8,4,2 and 32 repeatedly. Press PI-BUTTON 1 to switch the mode to the next test pattern (CONVERGENCE). Press PI-BUTTON 3 to select if the COLOR EDIT screen is displayed or not. (Refer to “(1) COLOR EDIT” on this article.) Pressing P1-START switch, the DISPLAY E S T exits, and then test menu screen appears.

Page 19
  • CONVERGENCE This screen is used for check and adjustment for display size, display position, ratio length to breadth and distortion.

CONVERGENCE

CROSS HATCH PATTERN

COLOR EDIT; P1-BUTTON Display how to enter the COLOR EDIT mode. NEXT COLOR TEST: P1-BUTTON 1 Display how to advance to the next test pattern. EXIT: P1-START Display how to return to the test menu screen.

The cross pattern called as “Cross hatch pattern” is displayed on the screen. Press PI-BUTTON 2 to select the color of cross hatch pattern in order of WHITE, BLUE, RED, VIOLET, GREEN, LIGHT BLUE, YELLOW, BLACK and WHITE repeatedly. Press P1-BUTTON I to switch the mode to the next test pattern (DIAGONAL). Press P1-BUTTON 3 to select if the COLOR EDIT screen is displayed or not. (Refer to “(1) COLOR EDIT” on this article.) Pressing P1-START switch, the DISPLAY TEST exits, and then test menu screen appears.

Page 20

5-2-2 SWITCH TESTI

This mode performs test for switches connected to PC board, such as buttons on the control panel. Pressing P1-BUTTON 3 and 4 at the same time, the test menu screen appears.

SWITCH TEST 1P: 0000 2P:0000

SERVICE: OFF COIN 1: 0 COIN 2: 0 TEST SW:OFF DIP SW1:OFF DIP SW2:0FF (The display is changed according to input EXIT: P1-BUTTON3 & 4 | Display how to return to the test menu screen.

§-2-3 SOUND TEST

This mode performs sound output test and speaker setting] MONAURAL/STEREO). Move P1:8-direction lever right and left to change the number of sound. Press P1-BUTTON 1 to play back the sound numbered on the display. Press P1-BUTTON 2 to select the mode STEREO/MONAURAL. Play back the sound number 001 for the stereo output test. Pressing P1-START switch, the test menu screen appears.

SOUND TEST

SONG: [000] Sound number STATUS: 0000 The status of sound output

SPEAKER OUT: STEREO Present mode (STEREO/MONAURAL) setting status

Display how to change the mode (STEREO/ SET "MONAURAL": P1-BUTTON 2 MONAURAL). EXIT : P1-START Display how to return to the test menu screen.

Page 21

EXIT:P1-START Display with regard to the JAMMA VIDEO standard (IVS) 5-2 JVS CABINET OPTIONS

This mode performs setting for cabinet corresponding to JAMMA VIDEO standard (JVS).

JVS CABINET OPTIONS <DEFAULTS IN GREEN,

VIDEO SYNC: Composite

JAMMA VIDEO STANDARD [STEP 1]

Main

I/ol

I/O 2

[Notice]

@ This article is not available if the cabinet is connected from the JAMMA edge connector on the PC board.

Press P1-BUTTON | to change the setting. Pressing P1-START switch, the setting screen exits, and then test menu screen appears.

  • VIDEO SYNC (Synchronizing signal output format of video output)

Compos!te (Composite synchronization) | Separate (Vertlca/horizontal _ synchronization) | Thick frame: initial value

[Notice]

@ Ifthe VIDEO SYNC is set at "Separate", the picture becomes more clear than "Composite". @ As for use of cabinet "CYBERLEAD" made by NAMCO, set the VIDEO SYNC at "Composite" if an apparatus is connected /o the line output display terminal at rear side. (Refer to "4-4 Explanation of external I/O terminal" on the instruction manual "CYBERLEAD".)

Page 22

This mode performs setting with regard to the contents of game, such as difficulty level of game and etc.

GAME OPTIONS <DEFAULTS IN GREEN>

DIFFICULTY LEVEL: MEDIUM FIGHT COUNT <1P GAME>: 2 FIGHT COUNT <VS GAME>: 2 LIFE BAR <1P GAME 110 LIFE BAR <VS GAME>: 140 t GUARD DAMAGE: OFF

  • | NEUTRAL GUARD: ON
  • | ROUND TIME: 40 SEC.

CHARACTER CHANGE AT CONTINUE: YES CHARACTER CHANGE AT VS GAME: NO

MUSIC IN ATTRACT: YES 1 EVENT MODE: OFF m)| HIT COLOR: RED

EX1T:P1-START

After selecting an item to be changed by moving the P1:8-direction lever up and down, press the P1- BUTTON 1 to change the setting. Pressing P1-START switch, the setting screen exits, and then test menu screen appears.

PICULTY LEVEL (Difficulty level of game)

EASY [ mepium— HARD | VERYHARD ULTRAHARD |

! Thick frame: initial value (The rest is the same)

1|2345
12345
-2-1NORMAL+1+2
2-1NORMAL+1+2
  • NEUTRAL GUARD (Guard in the condition that the lever is not be tilted.)

f CE TE F ir

Page 23
  • E (Time per | round [second])

CiYHARACTER CHANGE AT CONTINUE (Change of character at continue)

)) CHARACTER CHANGE AT VS GAME (Change of character on the player who is being challenged at vs game) (i

(K)MUSIC IN ATTRACT (Sound in attract)

  • EVENT MODE (Process after vs game)

RED (exist) GREEN (changed to another color)

Page 24

5-2-6 COIN OPTIONS

This mode performs setting with regard to the game fees, such as the credit number required for 1 play.

COIN OPTIONS <DEFAULTS IN GREEN>

START COST: 1 COIN TO START CONTINUE COST: 1 COIN TO CONTINUE COIN CHUTE1 MECHANICAL VALUE: 1 COIN COUNT AS 1 COIN COIN CHUTE2 MECHANICAL VALUE: 1 COIN COUNT AS 1 COIN CREDIT MODE: COMMON COIN COUNTER: 1 COUNTER FREE PLAY: NO

EXIT :P1-START

After selecting an item to be changed by moving the P1: 8-direction lever up and down, press the P1- BUTTON Ito change the setting.

Pressing P1-START switch, the setting screen exits, and then test menu screen appears.

[Notice]

@ It is impossible to change items (a) to (f) if “YES” has been set in (g) FREE PLAY. @ If the cabinet corresponding to the JAMMA VIDEO standard (JVS) is used for the game machine, items

  • and (f) are set automatically as an initial value so as to be suitable for the connection format on the cabinet. In this case, items (e) and (f) are not allowed to be changed.
  • START COST (Number of coins required for 1 new play)

1 IJZIE 8 COIN(S)TOSTART ! Thick frame: initial value (The rest is the same)

[Notice]

@ It is impossible to set (b) CONTINUE COST at the larger value than (a) START COST.

  • COIN CHUTE 1 MECHANICAL, VALUE (Number of coins added when the coin switch 1 works once) ICOINCOUNTAS _ 1] 4 [ » COIN
Page 25

UTE 2 MECHANICAL VALUE (Number of coins added when the coin switch 2 works once) 1 COIN COUNT As | COIN

REDIT M

T

| every coin switch works, and if every side, and the coin switch 2 corresponds | start switch is pressed.) to P2 side respectively.)

Notice

© Check if the coin switch 2 is connected correctly when setting (e) CREDIT MODE to “EACH ONE”; otherwise, a coin may not be accepted at P2 side and the play may not be available.

  • COIN COUNTER (Assignment of coin counter)

1 COUNTER 2 COUNTERS (Used | coin counter common to two (Used each coin counter for two coin switches respectively)

article] © In the case that a cabinet, which provides each | pair of coir, switch and coin counter for P1 side and P2 side respectively, is used: Setting (e) CREDIT MODE above to “EACH ONE”. (f) COIN COUNTER to “2 COUNTERS” after checking each one is connected correctly, each coin counting at P| side and P2 side is allowed to be logged separately.

  • FREE PLAY (Free play setting)

~T ADS. i=)

This mode allows to read the data with regard to the past play results, such as total play time by this time and etc. Press P1-BUTTON 1 to select the display screen. Pressing P1-START switch, the test menu screen appears.

Page 26

This mode performs clear for the data which is stored even if the power is turned OFF.

BACKUP DATA CLEAR

CANCEL ADS DATA CLEAR RANKING CLEAR SET DEFAULTS ALL OPTIONS ALL CLEAR

EXIT: P1-START Return to the test menu screen. Clear A.D.S data only. Initialization of ranking data. Initialization of all options. Clear all of data logged.

Display how to return to the test menu screen.

After selecting an item by moving the P1:8-direction lever up and down, press the P1-BUTTON 1 to perform the selected iter Pressing P1-START switch, the test menu screen appears.

  • CANCEL Return to the test menu screen.
  • ADS DATA CLEAR Clear A.D.S data only. (Refer to “5-2-7 A.D.S.”.)
  • RANKING CLEAR (Initialization of ranking data) Initialize all of ranking data, such as straight victories records and etc., at the value on delivery at factory.
  • SETDEFAULTS ALL OPTIONS (Initialization of all options) Initialize all options set in TEST mode. (Refer to “5-2TEST mode”.)
  • ALLCLEAR Perform the items (2) and (3) above at the same time.

5-2-9 EXIT & SAVE (Exit of TEST mode)

This mode returns to the game screen after exiting test mode.

[Notice]

@ If the exit of TEST mode is not performed in the correct procedures, a changed setting may not be reflected correctly. Be sure to select “EXIT & SAVE’ from the test menu screen before pressing P1- BUTTON Ito end it.

Page 27
  • Maintenance (i must beta

@ Do not remodel this game machine without our agreement; otherwise, an unexpected danger may happen.

WARNING @ Be sure to turn OFF the power switch of the cabinet before maintenance work; otherwise, an operator or another one may be Injured or struck by electricity.

[Notice] @ Be sure to use aJAMMA standard conformable one and a specified one for the JAMMA edge connector. @ Be sure to use a NAMCO specified one (DDK-made: 225D-10024C2-2312) for 48P extension edge connector (*))

The tests for switch, sound and display should be performed periodically to use this game machine in the correct condition. (Refer to “5-2 TEST mode”.) The running in the condition that the PC board is in loose fixing and connecting may cause a trouble or malfunction. Check the PC board periodically because that it is loosened.j due to vibration during play. An alien factor and ciduston the PC board may cause a trouble or malfunction. Clean the PC board periodically to keep it neat.

Notice]

® Be sure to turn OFF the power of cabinet before cleaning. Be sure to use an anti-static electricity cleaning tools, such as anti-static electricity brush for OA apparatus and etc.

If this game machine does not work correctly, check again. that this game machine is installed and set correctly after reading the instruction manual for cabinet and this manual. If the game machine does not work correctly after all efforts, contact your distributor after turning off the power of cabinet and removing the power plug from the outlet.

[Notice]

@ Do NOT perform continuity test through tester; otherwise, the internal voltage of tester may destroy the Ic.

  • 1) The JAMMA edge connector and 48P extension edge connector are used for only cabinet corresponding to the JAMMA standard.

7. Transportation

When sending PC boards due to transfer, resale and repair, wrap them with sponge or bubble wrap, and pack them in acard board boxes to protect against any shock from the outside.

Page 28

[Notice] ® Refer to the following list when connecting this game machine to the cabinet corresponding to the JAMMA standard. It is not necessary for cabinet corresponding to the JAMMA VIDEO standard (JVS). @ Be sure to read the concerned item on “4. Installation” when connecting it.

JAMMA edge connector (54P 3.96mm pitch) Extension edge connector (48P 2.54mm pitch) I Idering sid ¢ ( Speaker R (-) Speaker R (+) [Yellow] [Orange]

+5vpl]4|+svA3 | BS
"5A4 | B4
+12VF6 | +12vMis-insertionASBS5 Mis-insertion

protection key protection key

Mis-insertionH7 | Mis-insertionaeBe

protection key protection key

Coin counter 2J | 8 | Coin counter 1ATBF

P2-BUTTON 4

K9ee

[White, violet]

Speaker (-)L_|10 | Speaker(+)9 | Bo | GND [Black]
Audio (GND)M | 11 | Audio(+)GND [Black]
Video (GREEN) | N | 12 | Video (RED)anlau
Video (SYNC)P |13 | Video(BLUE)ap|Bb
Service switchR |14 | Video(GND)Aplaa
Ss15 | Test switchAl4 | B14
Coin switch 2T | 16 | Coin switch 1als[BIS

2 START U_ | 17 | PI-START switch oe Al6 | BIG

P2 lever (UP)v_ | 18 | Pl lever (UP)ant|B

P2 lever (DOWN) | W | 19 | PI lever (DOWN) Al8 | B18 \9 | PI-BUTTON4

P2 lever (LEFT)20 | PI lever (LEFT)[Violet]
P2 lever (RIGHT)21 | PI lever (RIGHT)SEBUT
P2-BUTTONZ | 22 | PI-BUTTON[Blue]
P2-BUTTON 2a | 23 | P1-BUTTON2;

b | 24 { f A24 | B24 GND e | 27 | GND GND f | 28 | GND